InterrogateSS - Revision history

Monica at 14:09, 27 August 2013

2013-08-27T14:09:16Z

Monica: /* Result parameters */

2013-08-26T08:02:14Z

‎Result parameters

Monica: Created page with "==Usage== This message is used between a MSC and a VLR and between the VLR and the HLR to retrieve information related to a Supplementary Service. ==Addressing== ... ==Inv..."

2013-08-26T08:01:43Z

Created page with "==Usage== This message is used between a MSC and a VLR and between the VLR and the HLR to retrieve information related to a Supplementary Service. ==Addressing== ... ==Inv..."

New page

==Usage==

This message is used between a MSC and a VLR and between the VLR and the HLR to retrieve information related to a Supplementary Service.

==Addressing==
...

==Invoke parameters==

* '''ss-Code''' – the code of the supplementary service to be interrogated.

* ''basicService'' – indicates for which basic service group the supplementary service should be interrogated. If not included, the interrogation request applies to all basic services. It's a choice between:
** bearerService – affected bearer
** teleservice – affected service

* ''longFTN-Supported'' - indicates that the mobile station supports Long Forwarded-to Numbers.

==Result parameters==

The set of parameters in the result depends on the invoke parameters, can be one of:

* ss-Status – the state information of the supplementary service that was interrogated. It is a comma separated set of the following flags:
** ''provisioned'' - service is supported by the HLR
** ''registered'' - service is registered for the subscriber, applies only to Call Forwarding
** ''active'' - service is active for the subscriber; for Call Forwarding the number must also be present
** ''quiescent'' - the service is active but is currently disabled because a higher priority service takes precedence. For example the '''baoc''' (Block All Outgoing Calls) service makes '''boic''' (Block Outgoing International Calls) become quiescent.

* basicServiceGroupList – list of
** basicService – identifies a bearer or a teleservice
** forwardingFeatureList – list of forwarding features:

* forwardingFeature – represents the information about each combination of a basic service and call forwarding
service. It is a list of the following parameters:
*** ''basicService'' – bearer or teleservice.
*** ''ss-Status'' - the state information of the supplementary service that was interrogated, see [[#ss-status|ss-Status]] above.
*** ''forwardedToNumber'' – the address to which a call is to be forwarded.
*** ''forwardedToSubaddress'' – refers to the sub-address attached to the address to which is to be forwarded.
*** ''forwardingOptions'' - refers to a forwarding option attached to a supplementary service.
*** ''noReplyConditionTime'' – refers to the timer for call forwarding on no reply.
*** ''extensionContainer''
*** ''longForwardedToNumber'' – an address to which the call is to be forwarded.

* genericServiceInfo – it is a list of the following parameters:
** ss-Status - the state information of the supplementary service that was interrogated, see [[#ss-status|ss-Status]] above.
** ''cliRestrictionOption'' – refers to the Restriction mode attached to the supplementary service. It can have one of the
following values:
*** permanent
*** temporaryDefaultRestricted
*** temporaryDefaultAllowed
** ''maximumentitledPriority'' – indicates the highest priority a subscriber is allowed to apply to an outgoing call setup.
** ''defaultPriority'' – defines the priority level that should be assigned if no explicit priority is indicated during call setup.
** ''ccbs-FeatureList'' – sequence of
*** CCBS-Feature – the necessary set of information requiered to describe a CCBS request. I can contain the following
parameters:
**** ''ccbs-Index''
**** ''b-subscriberNumber'' - number of destination B dialled by user A.
**** ''b-subscriberSubaddress'' - the sub-address attached to destination B.
**** ''basicServiceGroup'' – bearer or teleservice.
*** ''nbrSB'' - indicates the maximum number of parallel bearers that may be used as defined by the user's subscription.
*** ''nbrUser'' - is sent to register the MC maximum number of user defined circuit switched bearers to be used.
*** ''nbrSN'' - ...

==Example==

<component localCID="1" type="Invoke" operationCode="interrogateSS">
<ss-Code>allCallOfferingSS</ss-Code>
<basicService>
<teleservice>automaticFacsimileGroup3</teleservice>
</basicService>
</component>

==References==
* ETSI TS 100 974 V7.15.0 (2004-03) p1079

← Older revision		Revision as of 14:09, 27 August 2013
Line 1:		Line 1:
		+	{{DISPLAYTITLE:interrogateSS}}
	==Usage==		==Usage==

@@ Line 31: / Line 31: @@
 ** forwardingFeatureList – list of forwarding features:
-* forwardingFeature – represents the information about each combination of a basic service and call forwarding
+* forwardingFeature – represents the information about each combination of a basic service and call forwarding service. It is a list of the following parameters:
 service. It is a list of the following parameters:
 *** ''basicService'' – bearer or teleservice.
 *** ''ss-Status'' - the state information of the supplementary service that was interrogated, see [[#ss-status|ss-Status]] above.
@@ Line 44: / Line 43: @@
 * genericServiceInfo – it is a list of the following parameters:
 ** ss-Status - the state information of the supplementary service that was interrogated, see [[#ss-status|ss-Status]] above.
-** ''cliRestrictionOption''  – refers to the Restriction mode attached to the supplementary service. It can have one of the
+** ''cliRestrictionOption''  – refers to the Restriction mode attached to the supplementary service. It can have one of the following values:
 following values:
 *** permanent
 *** temporaryDefaultRestricted
@@ Line 52: / Line 50: @@
 ** ''defaultPriority'' – defines the priority level that should be assigned if no explicit priority is indicated during call setup.
 ** ''ccbs-FeatureList'' – sequence of
-*** CCBS-Feature – the necessary set of information requiered to describe a CCBS request. I can contain the following
+*** CCBS-Feature – the necessary set of information requiered to describe a CCBS request. I can contain the following parameters:
 parameters:
 **** ''ccbs-Index''
 **** ''b-subscriberNumber'' - number of destination B dialled by user A.
@@ Line 61: / Line 58: @@
 *** ''nbrUser'' - is sent  to register the MC maximum number of user defined circuit switched bearers to be used.
 *** ''nbrSN'' - ...
 ==Example==